工業冷水機的核心部分制冷系統主要由制冷壓縮機，冷凝器，膨脹閥，蒸發器等組成，并通過管道連接形成的一個封閉的制冷循環系統，其溫度范圍從1315大卡到1892000大卡，冷凍出水溫度范圍—20℃—+350℃。

　　冷水機安裝前請選擇地基平穩四周空氣暢通，空氣無污染，油氣少之場所，遮雨棚較好離機臺上方一米五以上，如使用時仍發現四周空氣悶熱，請加裝抽排風機，保持空氣對流，或將排出熱氣以排風管將其排出室外，這樣不但可以使冰水機增長使用年限，還可以提高效率，降低成冷水機本，安裝時環境溫度較好在35℃以下，確保機器較大發揮效能。

　　1.當壓縮機因某種原因發生故障時，此時水泵如繼續運行，可能會造成水溫急速升高，而當水溫超過50℃時，機內水管及水泵軸封極可能造成損壞漏水。

　　2.當壓縮機運行時高壓和低壓兩者差壓極少或相等時，即表示壓縮機本身閥片破損或斷裂，請即停止運轉并找專業人士進行處理。

　　3.如果發現漏冷媒部分浸于水中，立即停止冰水機運行，速將水箱內水排除，請專業人士進行處理，以免壓縮機將水吸入系統造成更嚴重損壞。

　　4.溫度開關應避免設定在5℃以下，防止蒸發器結冰。

　　現有的吹塑機在制備中空塑料制品的生產過程中，需將由吹塑機吹制成型的工件轉移至清飛邊工位實施清飛邊，清除飛邊后轉移至工業冷水機冷卻工位冷卻，現有的冷卻方式主要包括以下兩種：種為在吹塑機的模具內冷卻，能夠保證工件的成品質量，但耗時較長，影響吹塑機吹制的成型效率，第二種則采用出模后的自然冷卻方式，但工件在冷卻過程中易產生變形。

　　自然冷卻方式，一般需要將工件轉移至冷卻工位處，現有的搬運方式主要分為兩種：一種是利用鏟車或類似的機械搬運裝置，二是以手工方式搬運，前者的不足在于：由于無法對工件合理定位，因而在轉移過程中容易滾落并損及工件，并且鏟車難以將工件按工藝要求放置到冷卻工位的冷卻平臺的冷卻位(冷卻風噴嘴所在的位置)，后者則是由于塑料熔體溫度較高，在冷水機冷卻的過程中依舊會放出熱量，導致工作環境溫度較高，工作環境惡劣，在工作時，需要工人長時間站立進行工作，不僅工作效率不高，且工作勞動強度較大，易產生燙傷等傷害事故，且采用上述效果較差，成型率較為不佳，冷水機。